Turn the knob to navigate the display menu and adjust the wash time. Washing loose parts directly in the wash bucket - whether intentionally or accidentally - will damage printed parts, create noise, and may interfere with the agitation of IPA. Ensure parts are fully secured to the build platform when washing parts without the basket installed. Parts must be washed on the build platform and/or in the basket. Without a build platform installed, the basket can be removed by lifting vertically from the basket mount. Place parts directly in the basket after removing them from the build platform using the removal tool, scraper, or flush cutters. Parts can also be washed in the basket, either as an alternative or in addition to the platform mount. Whether using the build platform or basket as a wash method, the maximum single part size that can be washed in Form Wash is 14.5 × 14.5 × 17.5 cm (5.7 x 5.7 x 6.9 in). Align the top lip of the build platform with the arms of Form Wash’s platform mount, and fully insert to touch the back.įor a complete wash, ensure that IPA is filled between the minimum and maximum fill lines. Use the display and knob to raise the platform and basket mounts.įor convenience, install the build platform with printed parts directly in Form Wash to clean parts before removal. Wear gloves when handling parts and surfaces with IPA or uncured resin. Choose “End” to cancel the remaining time in the wash cycle while also stopping the agitation and lifting the platform and basket mount. Choose “Pause” to stop the agitation and lift the platform and basket mount, while maintaining the remaining time in the wash cycle. Check each material’s recommended wash time before beginning a cycle.Īfter beginning a wash cycle, the display shows the remaining time and additional menu options. Time: Press the knob to select and adjust the time, indicated in minutes.The wash cycle will not start until “Start” is selected. “Sleep” option lowers the mount and basket.“Open” option raises the mount and basket.“Start” option lowers the mount and basket and initiates the washing process.The following options are available from the main menu on the Form Wash display: Rotate the knob counterclockwise or clockwise to move between items in the menu, and press the knob to select an option. When connected to power, the display and knob provide the primary interface to program and operate Form Wash. Choose whether to wash the part on the build platform or in the basket. It is ready for use once the wash bucket has been filled between the minimum and maximum fill lines and the hydrometer is calibrated. The Form Wash automates the washing process. Note: Most of this section is taken from (). You may also need to use a chisel to scrape of any residual resin from The base of your prints to release the part. Remove Your PrintĪttach the build platform to the jig and slide the removal tool under Turn the platform over to prevent dripping while transferring to theįinish kit. When your print is finished, wear gloves to remove the build platform. Once the tank is full, your print will automatically start. Select the file name and confirm the print by pushing theīefore printing, the resin tank will fill and heat up to around 35° C. You will see your file uploading to the print queue on your printer’s Select which printer to upload the file to from the printer Sequence if you select “One Click Print.”Ĭonfirm your print’s material and layer height, then click the orange “generate all,” and “layout all.” PreForm will do these steps in For automatic set-up, use PreForm tools to “orient all,” Most parts print better when support at anĪngle. Through PreForm tools to explore basic functions for setting up your Opening PreForm, you will see the boundaries of the build volume and theīuild platform, which is inverted from the print orientation. Visit the product page to download the latest version of our software Be sure to remove the orange valve cover from the underside and press open the cap before starting a print, so that your resin tank fills correctly. Refer to step 9 on this SOP for preparing your print job with the PreForm SoftwareĪlign the cartridge with the opening in the back of the printer.Start the FormLabs PreForm software to load and prepare your 3D model for printing.Does not currently show any errors on its on-screen display.Is clear for a new print (not containing any remnants of previous print jobs).not currently working on any other jobs.Log into the controller PC for the FormLabs Form 2 3D printer.Questions, please ask any EPL student managers for help, or This guide will provide a walkthroughįor how to safely and efficiently use the Formlabs 3D printer so Welcome to the EPL! We’re excited you’re getting started with
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |